Site Overlay


for standard waveforms. The Agilent Technologies A Use the A to generate complex . Manual language options (please specify one). ABA US. For Safety information, Warranties, and Regulatory information, see the last page in this manual. Agilent A. Option Phase-Lock Assembly. oscilloscope or DMM and send it to your HP A for output. 3-year warranty. With your HP A, you get operating and service manuals, a quick reference .

Author: Moogujar Kajitaxe
Country: Iran
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 27 February 2018
Pages: 303
PDF File Size: 11.28 Mb
ePub File Size: 16.42 Mb
ISBN: 569-2-76736-273-6
Downloads: 47500
Price: Free* [*Free Regsitration Required]
Uploader: Malagore

The individual sine waves are harmonically related to each other — However, mamual cannot overwrite any of the five built-in waveforms. This cable has a 9-pin female connector on each end. The function generator is configured as a Data Terminal Equipment device. Chapter 1 Quick Start To store the instrument state To verify that the state was stored properly, you can turn the power off before recalling the state.

At power-on, the units for output amplitude are volts peak-to-peak. The Trig annunciator turns on when the function generator is waiting for a single trigger. Page Chapter 7 Tutorial Modulation Frequency Sweep Agilet A performs phase-continuous frequency sweeping — stepping from the sweep start frequency to the sweep stop frequency with between 2, and 4, discrete frequency steps.

The baud rate can be avilent from the front-panel only. An item that has been used previously. You are then exited from the menu.

The downloaded waveform is a square wave pulse 4, points with a calculated rise and fall time. Page 82 Chapter 3 Features and Functions Frequency Modulation FM Peak Frequency Deviation The peak frequency deviation represents the variation in frequency of the modulating waveform from the carrier frequency. I’m trying to disable the output of agilent A function generator.


Index string calibration, table of contents, 9 – 11 units output amplitude display message, technical specifications, – front-panel selection, 64 swapped byte order, terminals remote interface selection, SWE: Strange it doesn’t allow you to set the output to 0 V.

Contents Chapter 1 Quick Start To prepare the function generator for use 15 If the function generator does not turn on 16 To adjust the carrying handle 18 To set the output frequency 19 To set the output amplitude 20 To set a dc offset voltage 21 To set the duty cycle 22 To output a stored arbitrary waveform The output amplitude is automatically adjusted if you select a function whose maximum amplitude is less than that of the currently active function.

Quick Start One of the first things you will want to do with your function generator is to become acquainted with its front panel. The value or equivalent heating value specifies the ability of the ac signal to deliver power to a resistive load heat.

Table of Contents Add to my manuals Add. You may have misspelled the command or it may not be a valid command. Be sure to read the security code rules on page before attempting to secure the function generator. Page 31 Front-Panel Menu Operation Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab Add to watch list.


Read one error from the error queue. Manyal can select the manyal, frequency, amplitude, and offset all in one command. Seller assumes all responsibility for this listing. But is that same as disabling the output?

Get an immediate offer. Page 39 Chapter 2 Front-Panel Menu Operation A front-panel manal tutorial Menu Example 2 The following example shows how to use the recall menu feature as a shortcut to set the command back to its original setting. PNP transistor not working 2. Page Chapter 5 Error Messages Execution Errors Settings conflict; amplitude has been adjusted The requested output amplitude is not valid.

Agilent Technologies 33120A User Manual

Sell now – Have one to sell? Manuql section describes the low-level commands used to program the function generator. OFFS commands to select the function, frequency, amplitude, and offset of the carrier waveform. Joshua, Texas, United States. COPY command copies the waveform downloaded into memory to the specified name.


You connect the function generator to the interface using the 9-pin -9 serial connector on the rear panel. Page Agilent Technologies Sales ance of a U. Page 77 Chapter 3 Features and Functions Amplitude Modulation AM Modulating Source The function generator will accept an internal modulating signal, an external modulating signal, or both.