Shop Apt Imm24 Immersion Heater Controller + Box. Free delivery and returns on eligible orders. Part Number: IMM Housed in an impact resistant flush mount housing and supplied with a back box for surface mount applications. Slider switch On/Off and . Apt Immersion Heater Timeswitch ET16A 24 Hour model Specifications: Switch ON/OFF Rating, 1 (2) A Maximum w RGL Code (IMM24) &nb.
|Published (Last):||3 December 2006|
|PDF File Size:||20.29 Mb|
|ePub File Size:||8.77 Mb|
|Price:||Free* [*Free Regsitration Required]|
Would anyone please be a;t to help with the wiring? And this I believe are the diagrams for the Hive: Immm24 assuming that the Live out Pin 1 in the top picture from the IMM24’s are essentially Normally Open switched lives, and would just go respectively to 3 and 4 on the 2b diagram?
If so, is anything required in pins 1 and 2 in picture 2b? Nov 20, at 4: FlyingFish Wise Guy Joined: Jan 1, Posts: The wiring part is easy, you might need to find out why such high rated Watts switching is required, as I’m fairly sure not checked that a hive cannot switch 3.
APT Immersion Timeclock IMM24 Boiler Time Switch – Foglish Electrical
Thanks Mick – just to be clear – so the wiring comments I made sound ok? I doubt the APT is switching 3. Those timers are usually used to switch electric heater elements 3kw heaters. Not really imm4 for normal gas water and radiators. The hive uses a fairly standard backplate, depends on what plumbing plan you have, as to what control you need.
Nov 20, at 5: I should have provided more detail – the boiler is an external to the house – just outside the back door Vortex oil burner enclosure Riello RDB as we live in the sticks.
The hot water time clock is is just an separate immersion heater wired to said APT timer if we want hot water but don’t want to switch on the burner in summer for instance. Oct 18, Posts: Is that powering an electric immersion heater in the cylinder? I guess so by the imm part of the model code.
If that’s the case you won’t be able to use hive to control it.
APT Immersion Timeclock IMM24 Boiler Time Switch
The amps will be too high under load. I have seen 3a system timers fitted as immersion timers and they don’t last very long. What are the timers controlling? Is there a diverter valve for heating and hot water? Or is it a gravity hot water, pumped heating system?
Nov 21, at 3: Nov 21, at 4: Oct 20, Posts: No existing room thermostat?
As mentioned I think the previous owner had the boiler installed for emergencies. Problem is, the house has about 13 rads connected to it and to be brutally honest, we’ve never been able to get rads anything more than lukewarm using it.
Nov 21, at 6: I think your best course apr action is to get someone qualified and competent to assess your system and arrange a plan to get your heating and water functioning and performing correctly. I’d worry about smart controls as a secondary concern. Nov 22, at Nov 22, at 1: It sounds like you need a proper dual fuel setup that changes from one source to another lmm24 they do exist, or can be made up this would allow you to take heat from the multifuel appliance when it’s there, and then revert to using the oil boiler when it’s not.
The oil setup sounds like it needs converting into an S or Y plan depending on size and aot would allow you to gain timed and temperature iimm24 over both, and use something like a nest or hive.
For Immmersion Heaters 24HR 16A 230V
The immersion switching could then be done separate by a timer or given to your smart control through the use of a relay due to the load kw. Not sure if you’re serious about getting the electric gate man to look at your heating? A bit DIY, and you need to know how to wire up heating boilers and controls, but it might meet your current needs. Nov 22, at 2: Nov 22, at 3: Ok cool, yes you can wire the ch side of the hive into the switched live of the boiler, the pump control should be left to the boiler along with the permanent LNE, assuming the boiler is wired correctly as per the instructions you’ve linked above.
I want to set a apt IMM24 timer to come on at 5am. I have – Fixya
Talk to your sparky about having the hive dhw channel switching a correctly rated aot to power the immersion. This part is important, and should be an easy task for him. You risk a fire and damaging equipment if you try something else. This is mainly because you will be using your immersion more than most people as you can’t use the oil to heat the water on its own.
So in summer your immersion will be used a lot. As you won’t be using the heating. Nov 18, at 8: Nov 18, Posts: Hi OP Sorry to resurrect old thread. Something like below or a picture would be great if possible? Nov 18, at You must log in or sign up to reply here.
Your Username or Email Address: Do you already have an account?
No, create an account now. Yes, my password is: