This standard is issued under the fixed designation D ; the number 1 This practice is under the jurisdiction of ASTM Committee D on Protective. ASTM D Standard Practice for Surface Cleaning Concrete for Coating. ASTM D (Plastic sheet test): Place plastic sheet on concrete stab for 24 hours. o ASTM-D Standard Practice for Surface Cleaning Concrete for.
|Published (Last):||25 July 2013|
|PDF File Size:||9.82 Mb|
|ePub File Size:||15.38 Mb|
|Price:||Free* [*Free Regsitration Required]|
ASTM D – 05() – Standard Practice for Surface Cleaning Concrete for Coating
Check for compatibility by applying a test patch of the recommended coating system, covering at least 2 to 3 square feet. Procedures include broom cleaning, vacuum cleaning, air blast cleaning, water cleaning, detergent water cleaning, and steam cleaning. Brush Blasting or Sweep Blasting Includes dry blasting, water blasting, water blasting with abrasives, and vacuum blasting with abrasives.
Glossy surfaces should be sanded dull. Some composition boards may emit a waxy material that must be removed aztm a solvent prior to coating. Here is a summary of some of the published standards with which installers and specifiers of corrosion protection linings should be familiar.
Damaged areas must be repaired with an appropriate patching material. This standard is d4528 included in any packages.
ASTM D4258 – 05(2017)
All loose mortar and foreign material should be v4258 from block. Allow to dry and cure thoroughly for at least 30 days prior to painting. Surface preparation methods as outlined in ASTM D are required if the coating system is incompatible. The steps below are provided for assistance in properly preparing various common substrates before coating. Allow the coating to dry at least one week before testing for adhesion.
All of these steps were important to ensure the paint finish was smooth, uniform in color, and resilient. Mill scale, paint, and rust that is tightly adhered to the surface may remain even after Brush-Off Blast Cleaning.
Rooms must be heated in cold, damp weather. We have no amendments or corrections for this standard.
Staining to be cleaned may consist of light shadows, slight streaks, or minor discolorations caused by stains of rust, mill scale, or previously applied paint.
Already Subscribed to this document.
Please first verify your email before subscribing to alerts. Subscription pricing is determined by: Ensure that the surface is clean and free of any loose stucco, and that surface pH is between 6 and 9.
This practice includes surface cleaning of concrete to remove grease, dirt, and loose material prior to the application of coatings. Prime and paint as soon as possible after surface prep. Ensure that all surface contamination has been removed by washing with an appropriate cleaner.
You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server.
If necessary, pressure clean with a minimum of psi to remove all dirt, dust, oil, grease, laitance, loose particles, foreign material, and peeling or defective coatings. As the voice of the U.
Standard Practice for Surface Cleaning Concrete for Coating
Rinse carefully and allow to dry. When viewed without magnification, a White Metal Blast Cleaned surface should be free of any visible grease, oil, dust, dirt, mill scale, paint, rust, oxides, corrosion products, and other foreign matter. Wipe off the dust. Ensure that knots and pitch streaks are scraped, sanded, and spot primed before a full priming coat is applied. Small residues of rust and paint may be left in the lower portions of pits if the original surface is pitted.
Store finishing lumber and flooring in dry, warm rooms to prevent absorption of moisture, shrinkage, and roughening of the wood.
Conco Paints – Surface Preparation
Proceed to Checkout Continue Shopping. Clean steel using one or more of the nine surface preparations described below. Following these guidelines axtm help ensure sufficient adhesion of the coating and can help prolong the life of the coating system. There was so much to do before I ever opened a can of paint.
Surface imperfections should be corrected and cleaned prior to painting. Method of cleaning steel to remove dirt, oil, grease, loose rust, loose mill scale, and loose paint using water at pressures of wstm, to 2, psi at a flow of 4 to 14 gallons per minute.
Your Alert Profile lists the documents that will be monitored. Please first log in with a verified email before subscribing to alerts. If the document is revised or amended, you will be notified by email. Mill scale and rust cannot be removed by solvent cleaning.
Exterior composition board siding hardboard must be thoroughly cleaned and primed with an alkyd primer, whether factory primed or unprimed. High-pressure water blasting is commonly used to clean substrates. Profiled Increasing astmm surface area of the substrate by imparting a profile with some tooth gives lining systems more to grab on to.
When viewed without magnification, a metallic surface prepared according to this specification should be free of any visible grease, oil, dust, dirt, mill scale, paint, rust, oxides, corrosion products, and other foreign matter. Rinse with clear water and allow to dry.