Site Overlay

ATTANSIC ATTP1 PDF

, 13, ATTANSIC, -. Kring Electronics Co., Ltd. , -, Attansic, sop8. 63, 0, ATTANSIC, -. Rantle East Electronic. , -, ATTANSIC, SOP. 年12月11日 ATTP1_ – Technology Corporation ATTP1 Over Temperature Please contact Attansic Technology Corp. for the latest documents. Attansic. ATTP1. Tel:. MFG:. ATTANSIC. Picture. D/C:. 09+. QTY:. Packaging:. SOP8L. Package:. Note:. 原装正品. Support. No“ATTP1”Picture.

Author: Fenrilar Fenrinos
Country: Sri Lanka
Language: English (Spanish)
Genre: Business
Published (Last): 14 May 2011
Pages: 360
PDF File Size: 18.47 Mb
ePub File Size: 19.98 Mb
ISBN: 668-1-96387-413-9
Downloads: 31081
Price: Free* [*Free Regsitration Required]
Uploader: Nirn

So what is the solution? You don’t need to move the jumper though.

Check out our sister site! As for the other, yes you should solder pin 4 of the Attansic back attansix to the mobo. I find that the edge of a single-edge razor blade works rather well for helping lift this pin while I apply heat with the soldering iron. When the PSU is shutdown or in standby, this rail is dead, and all of atp1 items connected to the monitor inputs are no longer in a high impedance state.

I’ve personally verified this a few times myself, attnsic I know it works. I’ve got pretty steady hands and it took me three tries to get the jumper soldered correctly without bridging solder to the other pins. Apply a dollop of gel type super glue or some other fastening agent to each of your jumpers to near pin 97 and pin to keep them from flexing too much and breaking the pins off the chip.

  BASIC ENGINEERING DATA COLLECTION AND ANALYSIS VARDEMAN PDF

I use to type in short sentence.

Webb City, Mo Posts: However, be aware that soldering pin 97 and pin back down is rather tricky because of the fine spacing of the pins.

The wire will need to be about 8 cm 3″ long.

NF7-S CPU Thermal Diode Mod, Version – AOA Forums

Our members offer you their FAQs! This is the top right pin on the Attansic chip, when viewed with the mobo oriented as described above.

In my case, I actually took a chance with my CPU to try it out. It’s already in the right qttp1. The jumper wire will need to be about 3.

This is the 5vsb input. Also note that, because you are now monitoring the thermal diode directly, the thermistor in the socket is now rather pointless. A fine tip soldering iron is definitely a must. It didn’t change my temp readings at all, but it is theoretically possible for there to be a slight change in the reading.

ATTP1 Attansic CPU thermal protection controller chip SOP8

It is the 4th pin from the top right corner of the chip going down the right side of the chip, when viewed as described above. Anything else is nearly impossible. You’ll find that trying to solder the wires to the broken pins, while not impossible, is exceedingly difficult. As for the northbridge, does it have a thermal diode?

  GC BERKOUWER PDF

This is the analog voltage input. I will have no sympathy. The possibilities are endless!

It is the pin at the very top left corner of the Winbond chip on the top, when viewed as described above. Make sure you leave just a dollop of solder on the end of the jumper wire when you tin it or you’ll never get it to solder properly but don’t leave too much, or you’ll bridge the pins.

It is more likely that you will attnsic it up such that the OTP function trips prematurely and you aren’t able to power on the computer at all. You will need to carefully lift this pin from the solder pad.

ATTP1_1.3.pdf

BB code is On. Attznsic I understand your question correctly, then to restore the mobo back to default, you simply have to remove the mod. Lift this pin just as you did pin If you muck this up and turn your board into a doorstop, don’t come crying to me.