Dixell technology is leading the way in electronic regulation and control in the fields of refrigeration, air conditioning and heating, and retail. Dedication to. Dixell. Installing and Operating Instructions rel /02/ – cod. or faulty operation send the instrument back to the distributor or to “Dixell s.r.l.” (see. Digital controllers suitable for both heating and cooling applications. • Built in RS for connection to Dixell’s monitoring system. • Temperature control can be .
|Published (Last):||14 July 2009|
|PDF File Size:||7.53 Mb|
|ePub File Size:||5.1 Mb|
|Price:||Free* [*Free Regsitration Required]|
If set for hot gas, the compressor is kept running during defrost. Cooling — Differential is above rixel Set Point Heating — Differential is below the Set Point If a probe fault is detected the display will flash P1 and the controller will automatically cycle the compressor on and off.
XRC – DIXELL Israel
You will also find Pr2, which contains all parameters but requires a security xt100c to gain access. Tells the controller how many stages it is controlling.
If this parameter is set to 0. If necessary fit an auxiliary relay or contactor of an appropriate rating. This is even more important when extending probe cables.
Sets the time delay between the power to the controller being turned on and any output relay starting to operate. Innovation and efficiency for a better environment Dixell technology is leading the way in electronic regulation and control in the fields of refrigeration, air conditioning and heating, and retail.
Tells the evaporator fan to either run continuously apart from during defrost or to cycle on and off with the compressor.
Sets the time delay between a temperature or pressure alarm condition being sensed and the alarm being signaled during normal operation.
98473 – Digital Thermometer XR100C 230V
Other input types are 0 to 1v, 0 to 10v and 4 to 20mA. Enables the controller to be re-calibrated or off-set from the probe temperature reading. Sets the eixel minute 0. Then turn to the parameter list for your particular model, which has all the information you need on the various parameters, their functions and adjustment ranges.
If power spikes are likely to occur, fit a Varsities Part no. Configures the controller to inverse or direct action. The new version, designated v 2. Dedication to technological innovation and constant focus on efficiency have driven the development of solutions designed to maximize energy savings. Tells the controller whether to do an immediate defrost when the power is switched on or to wait for the normal interval time as set in parameter IdF.
All relays turn off.
This can be used to prevent short cycling of the compressor following a momentary power failure. Sets the initial temperature alarm delay time on start up so avoiding unnecessary alarms during pull down.
Digital Thermometer XRC V – Thermometer
This allows any residual moisture on the evaporator time to drip down and drain away. This parameter sets the override time during which the compressor will run continuously irrespective of the temperature.
A separate programming guide is available for the Universal-R. To omit a particular defrost period, set it to Panel mounted controllers have a frontal protection rating of IP Setting time to 0 to disables this function If a probe fault is detected the display xr00c flash P1 and the controller will automatically cycle the compressor on and off.
The Display The Buttons The controller is fitted with a display, which normally shows the current temperature. Sets the maximum duration time of the defrost Sets the temperature sensed by the evaporator probe, above which the count towards next defrost is suspended as set in parameter IdF Only functions if Smart Defrost is enabled see parameter EdF Sets the evaporator temperature at which the controller will terminate the defrost.
Setting time to 0 to disables this function Sets the period of time following a thermostat dixeel after dixek the controller will go into a defrost. Sets the maximum duration time of the defrost This tells the controller what to display during defrost. Access all Dixell manuals.
Hence these two energy saving cycles will overlap. Sets the lowest temperature to which the customer can adjust Set Point 1 Sets the lowest temperature to which the customer can adjust Set Point 2 Sets the highest temperature to which the customer can adjust Set Point 1 Sets the highest temperature to xt100c the customer can adjust Set Point 2 Sets the high temperature alarm level.
This only functions if the real time clock settings are lost. They can be used to control multiple stages, compressors, condenser fans, heaters or pumps.
98473 – Digital Thermometer XR100C 230V
Generally, these ‘safeguards’ are very inexpensive and may in some situations be looked upon as standard procedure where there is any doubt about the quality of the electrical supply or the effect of associated electrical equipment. The original model has now been upgraded. This can be used to prevent short cycling of the compressor following a momentary power failure, or to stagger the re-start of multiple units following a power failure, to prevent everything trying to start at once and blowing diixel fuse.
Sets the maximum temperature sensed by the evaporator probe above which the controller stops evaporator fans from running Sets the time delay between the end of defrost and the evaporator fans re-starting.
Allows the digital input to be used to mute a high or low level alarm from a remote button. Do not fit a controller in a place where it will be subjected to excessive vibration.
The factory dixle will differ accordingly.