Site Overlay


User Manuals · Request a Service · Request a Quote · Security Tips. Call us now on DSC – PC User Manual · DSC – PC User Manual. Index of /manuals/DSC/Intrusion Panels/PC Parent Directory · LED · PC Spanish User · PC User Until October 31/18, we’re offering free remote download setups for DSC and Ademco panels. We’ll make a Alarm Panel Programming Manuals, Programming Sheets and Setup Guides DSC PC Control Panel Programming Manual.

Author: Menris Gam
Country: Barbados
Language: English (Spanish)
Genre: Science
Published (Last): 28 March 2010
Pages: 379
PDF File Size: 7.38 Mb
ePub File Size: 8.89 Mb
ISBN: 795-7-26757-852-2
Downloads: 55122
Price: Free* [*Free Regsitration Required]
Uploader: Kagagrel

The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements.

Index of /manuals/DSC/Intrusion Panels/PC3000

Features which operational with a minimum of programming. It is completely provide the security ;c3000 design flexibility and selling programmable from the keypad. Enter the master code to entries that are as straight forward as dialing a telephone arm or disarm the panel. Terminal Connections switch to ground. A ohm current limiting resistor is connected in series. If the keypads are located a distance from the panel, install resistor circuits.

Each input must be terminated with a 1K an extra keypad temporarily at the panel during power up ohm E. Experiments using typical fires in family living units indicate that detectable quantities of smoke precede detectable levels of heat in most cases. The panel can be fully programmed from the keypad. The 16 Disarming zone lights and the fire alarm light provide alarm and status indication for the alarm circuits.

This trouble applies only to zones which have been programmed as day zones. A day zone mxnual same group of zones is bypassed each time, this bypass a trouble signal when the panel is disarmed and an alarm recall feature can be used instead of having to bypass Group B access code, any access code, or no code at all.


When the proper keys are pressed the keypad sounder and Keypad Zones the programmable output are activated for 5 seconds. There are three zones which can be activated from the keypad. Printer The printer must be capable of serial communication RS- Section [49] in the panel must be programmed to enable the See the downloading downloading when an answering machine is also connected manual for details on specific capabilities. In section [47], if zone light 7 is off, it is That The PC is programmed by entering instructions from is the numbers 0 through 9 and the letters A through F in the panel keypad.

Press [02] to programming examples mqnual the resulting transmission using program the next section, enter another section number or different formats for the reporting codes. After the exit delay has expired, an open on the mnaual will cause the entry Disarming with Access Codes 9 to 16 delay time to start.

PC – PC Security Products | DSC

During the entry time the keypad buzzers See section [13] for further information. The test transmission is sent to [5] Sescoa super speed the monitoring station to confirm that the communication link dzc Not used Wait for 10 seconds. In sections [01] through [15], do not enter any data dsv sections that are not used. Zones cannot be programmed for fast response – Do not use fast response devices on these zones.

If zone light is on, the zone can be Zone Light 2 bypassed using the [Q] [1] command.

Zone Light 1 to Group A. If zone light is on that code can be used to bypass. Zone Light 2 If an access code is not required to bypass zones, this Zone Light 3 section is irrelevant.

Auto-arm – no bell squawk Auto-arm – bell squawk Zone Light Code needed to abort auto-arm Any key to abort auto-arm Zone Light Connect the leads to the corresponding terminals on the panel. DO NOT connect multiple keypads on the same loop. Page of 44 Go. Table of Contents Add to my manuals Add. Installation Enter the master code to entries that are as straight forward as dialing a telephone arm or disarm the panel.


Terminal Connections Terminal Connections switch to ground. Trouble Display the bypass command is entered, pressing [99] recalls the 3 Day Zone Manusl User’s Programming Commands To review: Utility Output Command Group B access code, any access code, or no code at all.

Restoral Reporting Codes Zones 9 To 16 [08] Restoral Reporting Codes [11] Reporting Codes for Closing Zones 9 to 16 Arming with Access Codes 1 to 8 These reporting codes are used by the communicator to The reporting codes in sections [11] to [14] are used to transmit a zone restoral for zones 9 to Through [42] – For Future Use 2. Page 29 PC Version 7. Page 30 PC Version 7. Page 31 PC Version 7. Page 32 PC Version 7. Page manhal PC Version 7.

Page 34 PC Version 7. Page 35 PC Version 7. Page 36 PC Version 7. Page 37 PC Version 7.


Page 38 PC Version 7. Page 44 R Comments to this Manuals Your Name. Enter text from picture: By pressing ‘print’ button you will print only current page. To print the manual completely, please, download it. Don’t show me this message again. Got it, continue to print. Don’t have an account?